ipr press head — datasheet

ipr1000hP-110

Article no.: —
Werkzeugfinder Download as PDF
Technical data
Pressing force
960 kN
Operating pressure
850 bar
Max DIN size
85
Available crimp widths
25, 40, 60 mm *
Max cross-section
2500 mm²
Note
Sechskant (SK) bis Kennzahl 85; Achtkant (AK) bis Kennzahl 82; verpresst bis 2.500 mm² mit Achtkantpresseinsatz; für Isolationsdurchmesser von 250 mm
Fork inner Ø
110 mm
Fork width
40 mm
Dimensions
Ø 168 x 252
Weight
25.9 kg

* The crimp width depends on the specific press insert — see table below.

Build
Accessories
Special features
Compatible press inserts

41 press inserts are compatible with this press head (DIN size ≤ 85).

Designation KZ Press width mm Cu mm² Al mm² Al/St Aldrey
SK 13 13 25 — —
Steel sleeve:
120/20 150/25 70/23 132/17 Leopard 120/25 120/15 125/25 152/25 Ostrich 190/18 224/20 239/23 259/23 Groningen 381/20 476/24
—
SK 15 15 25 — —
Steel sleeve:
44/32 50/30 125/30 170/40 185/30 210/35 230/30 240/40 265/35 305/40 340/30 385/35 450/40 495/35 570/40 147/34 152/35,5 Piper 158/37 Wolf 191/31 242/32 242/39,5 Hawk 423/37
—
SK 17 17 25 — —
Steel sleeve:
210/50 300/50 380/50 510/45 560/50 650/45 74/43 Horse 120/42 184/43 Lynx 185/43 193/45 282/46 Dove 293/48 381/49 Bison
—
SK 19 19 25 — —
Steel sleeve:
95/55 435/55 97/56 Dorking 237/56 Lion 242/56 Hen 403/52 Condor 415/54 428/56 Zebra 537/53
—
SK 21 21 25 — —
Steel sleeve:
105/75 120/70 490/65 550/70 565/72 101/72 185/62 265/62 Bear 360/60 403/65 Drake 456/59 Canary 524/68
—
SK 23 23 25 — —
Steel sleeve:
680/85
—
SK 25 25 25
185
tension-resistant:
150
150
tension-resistant:
120
Alu sleeve:
44/32 50/30 120/20
120
SK 25B 25 40 60 — — — —
SK 28 28 25 — —
Alu sleeve:
125/30 150/25
Steel sleeve:
340/110
—
SK 28B 28 40 60 — — —
150 - 185
SK 30 30 25
tension-resistant:
185
—
Alu sleeve:
95/55 170/40 185/30
—
SK 30B 30 40 60 — — — —
SK 32 32 25 — — — —
SK 32B 32 40 60 — — — —
SK 34 34 25
tension-resistant:
240
300
tension-resistant:
240
Alu sleeve:
105/75 120/70 210/35 210/50 230/30 240/40
—
SK 34B 34 40 60 — — — —
SK 38 38 25
400
400
tension-resistant:
300
Alu sleeve:
265/35 300/50 305/40 340/30
—
SK 38B 38 40 60 — — — —
SK 42 42 25
500
—
Alu sleeve:
380/50 385/35
—
SK 42B 42 40 60 — — — —
SK 44 44 25
625
500
— —
SK 44B 44 40 60 — — — —
SK 46 46 25
tension-resistant:
500
—
Alu sleeve:
435/55 450/40 340/110
—
SK 46B 46 40 60 — — — —
SK 50 50 25
tension-resistant:
625
—
Alu sleeve:
495/35 510/45 490/65
—
SK 50B 50 40 60 — — — —
SK 52 52 25
800
625
Alu sleeve:
570/40 560/50 550/70 565/72
—
SK 52B 52 40 60 — — — —
SK 58 58 25
1000
800
Alu sleeve:
650/45 680/85
—
SK 58B 58 40 60 — — — —
SK 60 60 25
1200
1000
— —
SK 60B 60 40 60 — — — —
SK 62 62 25
1200
—
Alu sleeve:
1045/45 1055/45
—
SK 62B 62 40 — — — —
SK 66 66 25 — — — —
SK 68 68 25 — — — —
SK 70 70 25 — — — —
SK 72 72 25
1600
— — —
SK 76 76 25
1800
— — —
SK 80 80 25
2000
— — —
SK 85 85 25
2500
— — —
Cu / Al columns: tension-relieved / tension-resistant. The list shows all tool sizes approved for this press head.

Safety notice: Before use, please ensure that the correct press insert is used with the appropriate tool and material. Please refer to the tables. For any questions or discrepancies, please contact ipr werkzeuge.

Press insert holders
Notes & FAQ
For this tool

Concerns the press insert holders for ipr1000hP-110, ipr1500hP-130 and ipr1500hP-140. The number after the dash denotes the outer diameter of the press inserts and at the same time the inner diameter of the press head fork. The holders accept various press insert sizes and each has the dimension indicated after the dash: • The iprPA110 has an outer dimension of 110 mm. • The iprPA130 has an outer dimension of 130 mm. • The iprPA140 has an outer dimension of 140 mm. In principle the press inserts are compatible with the holders, because the coupling is of identical construction. This means press inserts with an outer diameter of 110 mm can also be coupled to the iprPA130 and iprPA140 holders. In principle there is nothing against using 110 mm press inserts in the iprPA130 holder. However, there are no tests that could prove usability with 100% certainty. To date no problems whatsoever have become known from practice. Press inserts with outer diameters of 110 mm and 130 mm can NOT be used with the iprPA140 holder, because the dimensional tolerance is different and the inserts therefore do not achieve force-locking (Kraftschluss). For using 130 mm press inserts in the ipr1500hP-140 press head, a special holder was designed: the iprPA140-for-130PE.
For all tools

Occasionally air in a hydraulic tool prevents it from working at full capability. The question is: how does the air get into the system? Please note the following: • After the hydraulic power unit's tank has been fully emptied and then refilled, the tank must be bled. • New hoses must be filled with oil before use. The same applies after hose testing. • If the nipples on the tool are replaced in-house, it is essential that whoever does so has first been instructed in bleeding the tool: when the fitted nipple is removed, the oil drains out and the oil chamber fills with air.
View all notes